View Full Version : Tech and Shop Talk
- Advice on a Boat Radio
- lifting a 03 chevy 1500
- Rock sliders
- Buying a new ride
- cutting torch kits?
- vortec vs non vortec
- Leaky injector
- Tires for Colorado or Montana
- Prominator, WTF is this?
- t-case slpine count
- PVC speaker tubes?
- fuel injector tech
- Bad duramax years?
- Rust Removal using Electrolysis
- sterling trucks
- 2006 Chevy Truck Radio Lights
- Jag question
- dana 300 to 231 doubler q's
- Trailer Registration Question
- Warn ti winch controler
- Warn 8274
- 1999 F150 IFS to Solid Front
- Can't find a driveshaft!!!
- 5.3 to th350
- Shop/Garages in College Station
- Cordless Drills
- 2003 LS-1 mated to 4L60E What's it worth?
- Wheel spacers: good bad and ugly
- Cummins will not start after a fuel filter change
- Which winch?
- How well do you know your hammers?
- Gasoline torch Kit
- Shaft & U-Joint replacement
- painting aluminum diamond plate?
- Electrical Switch Panels
- dual shocks
- need a tool
- Diff or T-case? Need help
- Clean your wenches!
- Electric Fuel Pump, Is a relay needed?
- Work day 12/6, 10am-?:??
- h-1 center?'s
- GM 6.0 troubles?
- BDR's big darn welding table build
- 4200 Vortec Info?
- 2006 ford fuel line fittings
- Electrical Issues... Need Help
- ATV Gas Tank Repair
- gear calculator?
- gears for cj
- Bend Tech Software
- Looking for help with Ford 8.8 swap
- Tool help
- Ford 9 inch
- HEI upgrade
- Question about gear install setup
- Chevy Starter suggestion when running long tube headers?
- Car lifts, what do you prefer, frame or tire lifts?
- stacking wheel spacers
- dual batteries
- Steering tech
- brake controller
- What do you wish was on your welding cart?
- Cleaning Fuel Injectors
- Tire pressure gauge (guage, quick, coupler, staun airdown)
- Weights of parts
- Need Tubing - Places?
- Tapping a 1980-96 Ford steering box
- Wiring for a jeep with an external voltage regulator?
- 1987 - 1992 Ford F-150 Alternator Upgrades
- rooftop tent mounting
- Suspension seats...
- Vertical Winch Mounting
- Need a hand Sunday
- OBDII Trouble Codes
- Hydro Aassist question
- Shocks on a 3/4 ton
- Resettable breakers VS. Fuses
- Transmission work
- Recommend a slide hammer?
- Mounting a M12000 on a Duramax...
- Duraminis
- 07 Dodge 5.9 diesel Voodoo
- CS144 Alternator Upgrade
- 1998 GMC 4.3L Computer Info
- 1356 Doubler, It's like Bigfoot
- I Need A Car
- Affordable C-Clip Dana 35 disk brake swap
- Esplain ECM programing to me
- The "Help keep Hot Pocket from Electricuting hisself" thread
- Tbi wiring harness
- Humvee Tires?
- Axle Identifiaction
- towing with the burb
- CB Radio
- how hard is it to intall some quarters?
- TJ axle nut size
- NV3550 leak
- Anyone have ford explorer knowledge?
- need some help
- Looking for a Diesel
- I think i found my leak.........this could be bad
- salvage yards
- Need some help with my d44
- Need a 22R Crank
- Tire Vulcanizing
- Help with some quick welding
- I got a question bout the toyota recalls.
- Registering an Antique Vehicle
- Anyone know anything about cb's?
- THE Roll Cage Thread
- Cj auto to manual converstion
- Long Term Jeep Storage
- Trailer registration and title
- Fricks turn to tear apart and not complete a Doubler
- Big Block Build
- General Grabbers
- Welding Cast Hints and Help
- Group Tube Buy
- NP205 suggestions?
- 2 Week Buggy
- DSP5 Switch Install (beware, diesel faggotry inside!)
- 1984 CJ7 ignition switch
- Cool Mechanical Gifs
- Weekend Mechanic 10/9-10th
- Post-Trip-Trauma
- Trail Safety: Fire Protection
- Worn timing belt
- Hanging heavy **** on a wall
- Driveshaft work in houston
- Truggy, wheelin trucks with bedsides?
- Someone help me make sense of what happened here...
- Any one have a tranny Jack?
- Oil leak?
- Jeep Gas Mileage
- Scrap
- Ford 2004 and up 5.4 spark plugs
- cheap spool gun
- can anyone make sense of this?
- Winch Fairlead Mount
- Who worked/s at S&S/ BAE?
- Synthetic winch rope
- Mid May Houston tube buy
- Regeaing a dana 35
- Welding Machines
- Save Babs the Benz
- C-6 no 3rd gear
- Stopped by Lee's place on the drive home today...
- Painting Help
- Junkyards in this area
- Cool Build Threads, Thread
- Opinions needed
- Chevy Tbi problems
- Anyone know of a good transmission shop in b/cs area?
- Winches and winching
- Houston Tranny shop?
- Favorite Rig Mods
- Tire Talk
- "Service Air Bag"
- Miller vs. Hobart - Any real difference?
- Gordon's still the junk yard to go to?
- The Wiring Thread
- My Shop Personalization
- Plasma Cutter in the B/CS area
- Friend Needs Help
- 63" semi camper posabilities
- gas bicycle
- DIY Tinting
- In Tank Fuel Intake
- Death Wobble Thread
- 2001 F350 Powerstroke 7.3
- radiator locations
- 98 ford ranger no start
- Anyone familiar with wiring for an LED light bar?
- Fuel/Air Ratio
- LED bars on a four wheeler
- Need some toyota knowledge
- Axles
- On board air
- Cutting Torch
- ford 351 q
- Help Setting up Dana 44 gears College Station
- 3-link/ Steering question
- Side by Sides
- Floor Jack Thread
- Cadillac with tracks
- Tractors!
- ARB parts
- Ecoboost vs 5.0
- New motor
- Opinions on getting 2dr or 4dr Rubicon.
- Oil issues
- dont what its called but its fun as SH!T to drive
- Show us Your Vintage Tools and Vintage Garage Stuff
- drivetrain combo in red cj
- best bang for your buck for efi systems?
- Oil Pan Skid
- Picked up a New(to me) Compressor
Powered by vBulletin® Version 4.2.2 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.