ford 9inch

[cj nut]

unsure of the ratio or the spline on the axles, one side is missing the drum and brake hardware. 40$ or just make an offer

[AggieTJ2007]

is it a big bearing carrier?

[colman]

how do you tell, it is at my house right now

[AggieTJ2007]

i don't know, google and search

[85cj7]

pick me pick me I know. . . .

[AggieTJ2007]

I don't care about the housing ends, the carrier is all I care about

[colman]

i don't know, google and search

well when you find out let me know

[73bronco]

stock carriers are all the same, only aftermarkets have the larger bearings. And there's several different types of housing ends.

[mudtoy67]

So it's complete except for brakes on one side? Where is it?

[colman]

it is also missing the yoke but it does come with a rim and ****ty tire bolted to it. it is in my driveway in bryan

[cj nut]

yea its at colmans along with all the other random crap i have

[mudtoy67]

trade?:confused2

http://tamor.org/forums/showthread.php?t=10694

[cj nut]

dont realy have a use for one i can use one at work whenever i need to. i prob can hold it for a bit if you need me too.

[tigweld]

that pic doesn't show anything except the difference in a disk brake housing or not, meaning the backing plates use 3/8's or 7/16" ,smaller meaning disk. the outer bearings are all the same size ,set 20 timken, but there are different variations of the bearing design(meaning some are sealed, some are not, some are tapered, some are regular roller) big bearing or small bearing means the carrier bearing, 3.125 is factory(up to 31 or 33 spline) 3.25 is what most aftermarket cases are so you can fit a 35 spline shaft


btw the race is stuck in the housing on the right that is why it looks smaller

[mudtoy67]

You don't need to hold it for me. If it's still around after new years I may pick it up anyway. Just thought I would trade something I don't need for something I don't need less.;)

[cj nut]

i know the feeling, i dought it will move before new years but you never know.

[colman]

well its not going anywhere till after new year cause i leave tomorrow and it is in my garage locked up.

[73bronco]

that pic doesn't show anything except the difference in a disk brake housing or not, meaning the backing plates use 3/8's or 7/16" ,smaller meaning disk. the outer bearings are all the same size ,set 20 timken, but there are different variations of the bearing design(meaning some are sealed, some are not, some are tapered, some are regular roller) big bearing or small bearing means the carrier bearing, 3.125 is factory(up to 31 or 33 spline) 3.25 is what most aftermarket cases are so you can fit a 35 spline shaft


btw the race is stuck in the housing on the right that is why it looks smaller

Wrong :) There are several different housing ends big,small,medium, and torino. You have to have the big bearing housing to use the 35spl and you can only get them with the tapered rollers instead of the stock sealed bearings.

[Seth]

right left nephew niece crown beer hikeschool geetar fams and stuffs

[robertf03]

i agree

[tigweld]

Wrong :) There are several different housing ends big,small,medium, and torino. You have to have the big bearing housing to use the 35spl and you can only get them with the tapered rollers instead of the stock sealed bearings.


the difference is the bolts, and bolt spacing, unless its a early bronc or a early passenger car housing, then there junk any way unless your trying to build a front leafspring housing.

I have a early passenger car 9" under my truck and it is a little different than the aftermarket ones I have put together. almost all of the repro stuff 4 9"s I have used is based of truck housing parts.

also the 2 different versions i can get to right now in my shop take the same outside diameter bearing but have way different bolt patterns

[mudtoy67]

Hey, I pm'd you big dummy. I can't believe anyone would go three days without signing on to TAMOR. We will teach you...you will learn.:flipoff2:

[colman]

its been sold