Free and Cheap parts

[eight]

Will not hold for you. First come, first gets.

Dana 60 rear 30 spline shafts. Fit ford truck axle. Think I have 3. $10 each

Dana 60 front drive flanges, dodge external, 30 spline. Have 2 or 4 to get rid of. $10 each.

D60 high steer arm. Used, drilled 3/4" straight thru. One only. $20

CJ aftermarket steering box mount. $25

CJ drop pitman arm, I think it's 4" and procomp brand. $20

Hydraulic cylinder. 1.5" bore x 8" stroke. Used, but I never used it, so not sure how good it is. Is an industrial tie rod cylinder so easy rebuild if it leaks. $25

Chevy d44 front long side inner axle shaft. $10

[Eckert]

well, damn.

[tommy53002]

Ill take the dana 44 and dana 300 yokes. thanks

[colman]

eckert get the hs arm, you need it

[eight]

You will also need to propose some sort of a plan of getting this stuff. It's in Houston, and I'm not shipping.

[eight]

Added some stuff.

[CheapJeep]

Is that CJ steering box mount supposed to keep the box from ripping off the frame? What brand is it?

I'll take 2 of the dana 60 drive flanges.

[stx4wheeler]

I'll take the other set of drive flanges and Dana 60 1330 yokes

[eight]

Yes Robbie, that steering box mount is supposed to keep it from ripping off the frame. I don't know what brand it is, it's gray.

Frick, I'll throw those yokes in the pile with your other stuff.

You both aware of what "external" means on the flanges? I think only dodge used them, up to 90 or something.
http://www.pirate4x4.com/tech/billavista/60_front/images/dodge_60_with_external_flange_2_small.jpg

[NealtheDestroyr]

Dibbs on the dana 30 yoke please

[eight]

No dibs, dibs sucks. If you or somebody comes up with a plan to get stuff to BCS, you can have them. If somebody else gets them before that happens, there is no being pissed off.

[Eckert]

eckert get the hs arm, you need it

i want the rear D60 shafts as well. unless you know some one going through houston soon back up to BCS. ill stick with my original statement of, damn.

[eight]

Picture of hydraulic cylinder.

http://img.photobucket.com/albums/v160/ryankopecki/misc/100_0130.jpg

[colman]

if i can find a way to meet you in the next few weeks i will take the ps boxes for cory and the mount. i might be in houston at the end of next weekend. i will get back to you as soon as i find out

[tommy53002]

Where in Houston? My Dad works in houston I could get him to meet you somewhere.

[NealtheDestroyr]

No dibs, dibs sucks. If you or somebody comes up with a plan to get stuff to BCS, you can have them. If somebody else gets them before that happens, there is no being pissed off.

no problem ill figure something out

[eight]

I'm at Fairbanks and 290.

D30 and D44 yoke are the same. Not sure how many I have. They say a d300 yoke is also the same, but I think I tried it years ago and it didn't seal. There should only be one d300 yoke. I can just give the lot of them to Matt or Tommy and yall can sort them out. Should be a couple for each of you.

[eight]

I've updated the list above for what I still have. Can bring parts to Alto/Shiloh run.

[mudtoy67]

Are CJ and Waggy pitman arms interchangeable? I might take that off your hands.

[85cj7]

Are CJ and Waggy pitman arms interchangeable? I might take that off your hands.

yes waggy and cj pitman arms are the same spline and indexing. The cj arm uses a smaller tre so would have to be reamed for a waggy tre. BDR if you have a stock waggy arm I could really use it. Give ya $20 for it:confused: