View Full Version : 4L80E torque converter dust cover, ASAP
Sharpe
03-16-2010, 09:11 AM
Frag'd mine, need a new one pronto to get the DD back together. TH400 one will NOT fit.
Reckless
03-16-2010, 09:16 AM
****, i just sold mine
Sharpe
03-16-2010, 09:52 AM
$25 from the dealer, can get it tomorrow morning. Still tryin to find one today though.
agjohn02
03-16-2010, 10:18 AM
why is this something you need ASAP. is it needed to drive the truck?
uglyota
03-16-2010, 10:22 AM
I bet john's transmission would sell you one
Sharpe
03-16-2010, 10:33 AM
why is this something you need ASAP. is it needed to drive the truck?
Technically not but considering I would have to drop the exhaust and front driveshaft again to re-install it later, I want to get it replaced before I put everything back together. Its also proven to have done its job of protecting the torque converter once already, so its worth replacing. Not to mention the 6 bolts holding it to the transmission bellhousing and 2 torque rods that bolt to it tell me its somewhat structural in nature.
agjohn02
03-16-2010, 10:37 AM
ah, im thinking of a 4L60E with the little plastic dust covers. i wasnt aware that an 80 had a full lower cover similar to the old syle.
DRAGOONRANCH
03-16-2010, 11:00 AM
How'd you frag it?
Sharpe
03-16-2010, 11:15 AM
Trying to hammer a dent out. Cast aluminum only like to get bent once...
DRAGOONRANCH
03-16-2010, 11:26 AM
ok, how'd you get the dent in it?
Sharpe
03-16-2010, 11:50 AM
Dunno.
TdmayfieldIV
03-16-2010, 12:27 PM
just put some duct tape over the hole
uglyota
03-16-2010, 01:50 PM
frag'd=fragmented
=duct tape don't fix that
TexTJ209
03-16-2010, 02:46 PM
frag'd=fragmented
=duct tape don't fix that
It does if you use enough of it.
bcolman
03-16-2010, 09:46 PM
jb weld?
agjohn02
03-16-2010, 10:58 PM
jb weld?
Only works on ford transmissions.
Sharpe
03-17-2010, 08:23 AM
jb weld?
Tried it, will post pics later :laughing:
Sharpe
03-17-2010, 10:18 AM
F U C K F U C K F U C K F U C K F U C KGM discontinued the heavy cast aluminum cover and replaced it with a flimsy stamped steel piece of ****. It doesnt even have the ****ing torque rod mounts on it :angry::angry::angry::angry:
KrazyKarl02
03-17-2010, 10:33 AM
If you would have stuck with JB Weld, none of this would have been an issue.
TdmayfieldIV
03-17-2010, 02:50 PM
It does if you use enough of it.
+
jb weld?
=strongest repair evar!!!
oh and forget bolts, hold it on with zip ties
bcolman
03-17-2010, 05:48 PM
have you tried the junk yards?
CheapJeep
03-17-2010, 09:51 PM
Dust covers are overrated, just mount the torque rods straight to the bellhousing and use shorter bolts...:D
cj nut
03-20-2010, 08:04 PM
if you still need one let me know i may have a buddie in cs with one.....
colman
03-20-2010, 09:32 PM
i hope your not talking about me
Powered by vBulletin® Version 4.2.2 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.