Work Weekend/Newbie Run to 47 or Alto 2/12-13

[MR.ZAP]

Alright guys I know somebody has to fix some stuff on their rig, so how does Saturday sound for a work day (Travis)? Tommy is supposed to talk with Steve about a 47 run on Sunday and if that falls through we can always do Alto. New guys, this is a perfect opportunity to get your windshield banner! :gigem:

[bcolman]

travis, do you have your welder back, i may be in for this, ill know more by the end of the week

[Sparling]

No, his welder and plasma are still in houston

[BroncoJo]

This should work, I might could get by welder back.

[MR.ZAP]

Bad ass. I need to fix my winch :D

[sam_hodnett]

I could use some help figuring out the 4X4 on buckwheat

[Sparling]

I'd be down for working on other peoples **** since mine is in San Antonio

[BroncoJo]

I could use some help figuring out the 4X4 on buckwheat

First figure out these two questions:

Does any axle shafts spin?
Does the Drive shaft spin?

[Hot Pocket]

Down for 47, not down for Alto

[MR.ZAP]

Okay so what's the interest level in this as of today?

[DRAGOONRANCH]

If a trip to Alto pans out I could tow simeone if you have a trailer. If no tow needed I will just load up a 4# Wheeler and meet y'all out there. If its a 47 run I would just like to get a trail seat.

[Sparling]

I'm still down to watch other people break their ****. I don't have a rig so sunday I'd need a trail seat if I went.

[sam_hodnett]

I will need a seat Zap, and im down for working on stuff

[Sparling]

Travis, do you have a torch at your place? I feel like making a knife.

[TdmayfieldIV]

I'll call steve tomorrow. Work weekend starting 1pm on saturday at travis' house. We have a stick welder and a mig and plasma might be coming too. We need someone to bring a floor jack.

[BroncoJo]

Dodge needs new u-joints, I think.


No torch

[MR.ZAP]

I'll call steve tomorrow. Work weekend starting 1pm on saturday at travis' house. We have a stick welder and a mig and plasma might be coming too. We need someone to bring a floor jack.

Awesome, thanks man.

[breckboarder55]

So welder on hand? Is there a line?

I still need to make (I'll really need help with this) my new shock mounts.

[MR.ZAP]

Tommy... Wtf have you called steve yet? For the eighth time haha

[TdmayfieldIV]

Stop being a douche. I just got his number. I told you yesterday that I was working on it. I lost all of my numbers when I had to reset my phone. For the love of god you're like a woman.

[MR.ZAP]

Okay any more takers for a run tomorrow? As of right now we don't have enough rigs to make it a worthwhile run.

[Sparling]

Sam, get the pictures and video up or email them to me so I can do it.

[MR.ZAP]

Sam, get the pictures and video up or email them to me so I can do it.

hahahahaha, yes!

[sam_hodnett]

Sorry, cant find the cable for my camera, and it is a sony, so its memory card wont work with my computer, it might be a while

[Sparling]

I think I have the same camera...

10.1 megapixel sony cybershot?

[sam_hodnett]

I think I have the same camera...

10.1 megapixel sony cybershot?

12, but the cable is probably the same

[MR.ZAP]

Nobody else wants to wheel? Steve said to come out at two but if there's no interest then we may scrap the run.

[BroncoJo]

Nobody else wants to wheel? Steve said to come out at two but if there's no interest then we may scrap the run.

Call him if yall don't make it

[tommy53002]

I dont have my jeep going but I'd take my xterra out there if yall go.

[MR.ZAP]

Alright two fifteen at mcdonald's on northgate.

[MR.ZAP]

Tyler Cross and I went out there. Overall it was a good day. His CJ performed well although his carbureted 350 had problems with a few of the hills. We followed Steve around, who was riding shotgun in the Explorer. Had a good time out there, place was packed but we only ran into other rigs once.

[TdmayfieldIV]

sweet, I had too much to do to go out. I ended up making it a 2 day work weekend. Installed the other side molly shaft and worked on the brakes some.

[BroncoJo]

sweet, I had too much to do to go out. I ended up making it a 2 day work weekend. Installed the other side molly shaft and worked on the brakes some.

It takes two days to install axle shafts? :flipoff2:

[tommy53002]

Alright two fifteen at mcdonald's on northgate.

Did yall go? I would have went but I heard from Tommy that it was a bust..

Nevermind, I just read the other posts.

[MR.ZAP]

Did yall go? I would have went but I heard from Tommy that it was a bust..

Yeah man, Tyler Cross and I headed up there. Waited for you for a little bit but left the McDonalds parking lot at about 2:35

[Sharpe]

It takes two days to install axle shafts? :flipoff2:

Last time it took a month so he's making progress...

[TdmayfieldIV]

it only took me 45 min per side. We got distracted on sat and played with the big tire for a while. And then we rti'ed everthing at Travis' house.

[TdmayfieldIV]

Did yall go? I would have went but I heard from Tommy that it was a bust..

I didn't think they were, sorry.

[JB]

damn

[Tyler]

I thought it was a pretty good trip. Definitly need a carb solution. It just takes me a little longer and a little more skinny pedal than the fuel injection guys. :mad:

[Sparling]

http://www.youtube.com/watch?v=bbpoKFRjI08

[bcolman]

http://www.youtube.com/watch?v=bbpoKFRjI08

whose laughing like a little girl? tommy?

[BroncoJo]

whose laughing like a little girl? tommy?

Good guess but I think it is Sam

[bcolman]

that would have been my second guess

[Seth]

need a hill.

[sam_hodnett]

that would have been my second guess

:flipoff2: