Dodge Dana 60 Kingpin with high steer arms, forged yoke, etc...

[Doug Krebs]

Not sure why I never posted this over here... I copied it from another forum, so if anything is missing just ask questions.

Has the following:

Forged 1350 yoke
High steer arms/tie rod behind the axle
Uses 8 ARP studs on the arms rather than bolts.


Calipers/pads/rotors/kingpins all brand new 2 years ago. They have less than 100 miles on them. I wheeled it 3 times since the dana 60 was installed and parted it out last year.

I can't remember if I welded just the spider gears or welded them to the carrier. Has 4.10's, but the threads on the pinion nut are fubared. If it's taken off again, I doubt the pinion would be reusable.

Does not include the tie rod/drag link and brake lines that are in the pictures...

Price is $1200 located in bryan.

Edited to add pics:

I dragged the axle outside knocked the surface rust off the rotors and washed it. I might get some better pics tomorrow at lunch. It was getting late when I took the pics.

http://lh6.ggpht.com/_hA-3cmmzlSY/S423mzDFl_I/AAAAAAAAEZ0/cInXImuAl7E/DSC_0429.JPG
http://lh6.ggpht.com/_hA-3cmmzlSY/S423n0AtlWI/AAAAAAAAEZ4/Glhnc9NcLL0/DSC_0430.JPG
http://lh6.ggpht.com/_hA-3cmmzlSY/S423ojf-yaI/AAAAAAAAEZ8/nlup0KUDGN8/DSC_0431.JPG
http://lh3.ggpht.com/_hA-3cmmzlSY/S423pbXsg7I/AAAAAAAAEaA/YIVvXkrFPTg/DSC_0432.JPG
http://lh3.ggpht.com/_hA-3cmmzlSY/S423qJGt8FI/AAAAAAAAEaE/1milLwg31wk/s512/DSC_0433.JPG
http://lh6.ggpht.com/_hA-3cmmzlSY/S423qvxuVRI/AAAAAAAAEaI/FpcWwK8rnlU/DSC_0434.JPG
http://lh3.ggpht.com/_hA-3cmmzlSY/S423rL5RxwI/AAAAAAAAEaM/tu0d-vFCf8E/DSC_0435.JPG
http://lh6.ggpht.com/_hA-3cmmzlSY/S423r6YlwGI/AAAAAAAAEaQ/YFVWzIQ_okA/DSC_0436.JPG
http://lh4.ggpht.com/_hA-3cmmzlSY/S423sdiRRWI/AAAAAAAAEaU/Y8-3rWIIenc/DSC_0437.JPG
http://lh4.ggpht.com/_hA-3cmmzlSY/S423tEwe7SI/AAAAAAAAEaY/MOcq9nf3EFg/DSC_0438.JPG

[Doug Krebs]

Couple of day time pics:
http://lh5.ggpht.com/_hA-3cmmzlSY/S46t8Wv5qQI/AAAAAAAAEbc/pUUVe_v3qYU/DSC_0442.JPG
http://lh3.ggpht.com/_hA-3cmmzlSY/S46t9H1YDnI/AAAAAAAAEbg/1UtuW4hy-CI/DSC_0443.JPG
http://lh3.ggpht.com/_hA-3cmmzlSY/S46t9_v50BI/AAAAAAAAEbk/k6xU_CYrvaA/DSC_0444.JPG
http://lh5.ggpht.com/_hA-3cmmzlSY/S46t-y8Lq1I/AAAAAAAAEbo/dBarc0aZHXo/DSC_0445.JPG
http://lh5.ggpht.com/_hA-3cmmzlSY/S46t_rUYnEI/AAAAAAAAEbs/hwxfMtGMyl8/DSC_0446.JPG
http://lh5.ggpht.com/_hA-3cmmzlSY/S46uBiQgEtI/AAAAAAAAEcU/eGSmg37Sbcw/s512/DSC_0447.JPG

[Doug Krebs]

hell might as well bump this... email me as I rarely get on here. dougkrebs02 at gmail

[Doug Krebs]

Still holding down the garage floor! email me at the address above.

[Doug Krebs]

Almost a year, might as well bump this!

[Fredo]

I think you need to just find a rig to put this under and come back to the world of offroading Doug. It's still a lot of fun in case you forgot. :D :flipoff2:

[Doug Krebs]

I think you need to just find a rig to put this under and come back to the world of offroading Doug. It's still a lot of fun in case you forgot. :D :flipoff2:

Maybe in a few years, and I've got a Ford High Pinion saved for that.

[BMFScout]

I am a buyer if you can provide warranties on the parts. I think most of them have a 10 year deal...

[Doug Krebs]

Sold a few days ago for $700 minus the steering setup. Now I can buy some speakers!