Doug Krebs
10-18-2011, 12:36 PM
Not sure why I never posted this over here... I copied it from another forum, so if anything is missing just ask questions.
Has the following:
Forged 1350 yoke
High steer arms/tie rod behind the axle
Uses 8 ARP studs on the arms rather than bolts.
Calipers/pads/rotors/kingpins all brand new 2 years ago. They have less than 100 miles on them. I wheeled it 3 times since the dana 60 was installed and parted it out last year.
I can't remember if I welded just the spider gears or welded them to the carrier. Has 4.10's, but the threads on the pinion nut are fubared. If it's taken off again, I doubt the pinion would be reusable.
Does not include the tie rod/drag link and brake lines that are in the pictures...
Price is $1200 located in bryan.
Edited to add pics:
I dragged the axle outside knocked the surface rust off the rotors and washed it. I might get some better pics tomorrow at lunch. It was getting late when I took the pics.
http://lh6.ggpht.com/_hA-3cmmzlSY/S423mzDFl_I/AAAAAAAAEZ0/cInXImuAl7E/DSC_0429.JPG
http://lh6.ggpht.com/_hA-3cmmzlSY/S423n0AtlWI/AAAAAAAAEZ4/Glhnc9NcLL0/DSC_0430.JPG
http://lh6.ggpht.com/_hA-3cmmzlSY/S423ojf-yaI/AAAAAAAAEZ8/nlup0KUDGN8/DSC_0431.JPG
http://lh3.ggpht.com/_hA-3cmmzlSY/S423pbXsg7I/AAAAAAAAEaA/YIVvXkrFPTg/DSC_0432.JPG
http://lh3.ggpht.com/_hA-3cmmzlSY/S423qJGt8FI/AAAAAAAAEaE/1milLwg31wk/s512/DSC_0433.JPG
http://lh6.ggpht.com/_hA-3cmmzlSY/S423qvxuVRI/AAAAAAAAEaI/FpcWwK8rnlU/DSC_0434.JPG
http://lh3.ggpht.com/_hA-3cmmzlSY/S423rL5RxwI/AAAAAAAAEaM/tu0d-vFCf8E/DSC_0435.JPG
http://lh6.ggpht.com/_hA-3cmmzlSY/S423r6YlwGI/AAAAAAAAEaQ/YFVWzIQ_okA/DSC_0436.JPG
http://lh4.ggpht.com/_hA-3cmmzlSY/S423sdiRRWI/AAAAAAAAEaU/Y8-3rWIIenc/DSC_0437.JPG
http://lh4.ggpht.com/_hA-3cmmzlSY/S423tEwe7SI/AAAAAAAAEaY/MOcq9nf3EFg/DSC_0438.JPG
Has the following:
Forged 1350 yoke
High steer arms/tie rod behind the axle
Uses 8 ARP studs on the arms rather than bolts.
Calipers/pads/rotors/kingpins all brand new 2 years ago. They have less than 100 miles on them. I wheeled it 3 times since the dana 60 was installed and parted it out last year.
I can't remember if I welded just the spider gears or welded them to the carrier. Has 4.10's, but the threads on the pinion nut are fubared. If it's taken off again, I doubt the pinion would be reusable.
Does not include the tie rod/drag link and brake lines that are in the pictures...
Price is $1200 located in bryan.
Edited to add pics:
I dragged the axle outside knocked the surface rust off the rotors and washed it. I might get some better pics tomorrow at lunch. It was getting late when I took the pics.
http://lh6.ggpht.com/_hA-3cmmzlSY/S423mzDFl_I/AAAAAAAAEZ0/cInXImuAl7E/DSC_0429.JPG
http://lh6.ggpht.com/_hA-3cmmzlSY/S423n0AtlWI/AAAAAAAAEZ4/Glhnc9NcLL0/DSC_0430.JPG
http://lh6.ggpht.com/_hA-3cmmzlSY/S423ojf-yaI/AAAAAAAAEZ8/nlup0KUDGN8/DSC_0431.JPG
http://lh3.ggpht.com/_hA-3cmmzlSY/S423pbXsg7I/AAAAAAAAEaA/YIVvXkrFPTg/DSC_0432.JPG
http://lh3.ggpht.com/_hA-3cmmzlSY/S423qJGt8FI/AAAAAAAAEaE/1milLwg31wk/s512/DSC_0433.JPG
http://lh6.ggpht.com/_hA-3cmmzlSY/S423qvxuVRI/AAAAAAAAEaI/FpcWwK8rnlU/DSC_0434.JPG
http://lh3.ggpht.com/_hA-3cmmzlSY/S423rL5RxwI/AAAAAAAAEaM/tu0d-vFCf8E/DSC_0435.JPG
http://lh6.ggpht.com/_hA-3cmmzlSY/S423r6YlwGI/AAAAAAAAEaQ/YFVWzIQ_okA/DSC_0436.JPG
http://lh4.ggpht.com/_hA-3cmmzlSY/S423sdiRRWI/AAAAAAAAEaU/Y8-3rWIIenc/DSC_0437.JPG
http://lh4.ggpht.com/_hA-3cmmzlSY/S423tEwe7SI/AAAAAAAAEaY/MOcq9nf3EFg/DSC_0438.JPG