Very close call

[Graystroke]

Take a look at these. These are the big end bearings off of the Mack. Notice th oilling hole...maybe the reason the oil pressure was only around 30 PSI running down the HWY. Suppose to be 60 PSI. When I was driving down to Stephenville (before the UFO sightings :flipoff2: ) I noticed a slight knock when coasting...didn't hear it accelerating under load...figured it might be a rod. We took it into the shop on the way back...mechanic said same thing. really close call...crank was ok, replaced all the rod bearings and mains, new oil pump, new rod on that hole (it was out of round and needed re-sizing), new rings. should be good for another million. :gigem:

[DRAGOONRANCH]

http://i47.photobucket.com/albums/f192/DRAGOONRANCH/GIFS/homersimpson.gif

[Fredo]

Put new bearings in their place?....weak sauce.

http://tamor.org/forums/showthread.php?t=6389&highlight=gentleman

[Graystroke]

Put new bearings in their place?....weak sauce.

http://tamor.org/forums/showthread.php?t=6389&highlight=gentleman
IH motor $200. 300HP Mack $6500 USED running 600k plus miles not including installation. I'll take the cheap weak sauce.

[Fredo]

joke [johk] noun, verb, joked, jok·ing.

–noun
1. something said or done to provoke laughter or cause amusement, as a witticism, a short and amusing anecdote, or a prankish act: He tells very funny jokes. She played a joke on him.
2. something that is amusing or ridiculous, esp. because of being ludicrously inadequate or a sham; a thing, situation, or person laughed at rather than taken seriously; farce: Their pretense of generosity is a joke. An officer with no ability to command is a joke.
3. a matter that need not be taken very seriously; trifling matter: The loss was no joke.
4. something that does not present the expected challenge; something very easy: The test was a joke for the whole class.
5. practical joke.

–verb (used without object)
6. to speak or act in a playful or merry way: He was always joking with us.
7. to say something in fun or teasing rather than in earnest; be facetious: He didn't really mean it, he was only joking.

–verb (used with object)
8. to subject to jokes; make fun of; tease.

[jerryg79]

grayson, you have become a crochety old internet fecker in the last two weeks. What gives?

[mudtoy67]

grayson, you have become a crochety old internet fecker in the last two weeks. What gives?


Frequent urination. It's too hot in the house. Mood swings.








That's just from getting old, don't forget his wife is pregnant too! :flipoff2:

[Graystroke]

sorry, I guess the internet doesn't show the inflection in my voice
maybe I should have said:


Put new bearings in their place?....weak sauce.

http://tamor.org/forums/showthread.php?t=6389&highlight=gentleman


[laughing] ha, ha, ha that's funny! except that a IH motor cost $200 if it throws a rod a Mack is $6500 if it does. now, I know what you said was a joke... don't get me wrong...I was just pointing out the fact that an IH motor is worth more in scrap.
followed by the obligatory triple: :flipoff2: :flipoff2: :flipoff2:
and one extra for good measure: :flipoff2:


PS I'm a dick!

[DRAGOONRANCH]

Frequent urination. It's too hot in the house. Mood swings.








That's just from getting old, don't forget his wife is pregnant too! :flipoff2:

BDR, what you do touches me in all the right places. :gigem:

[Graystroke]

well, after one of the heads was pulled, top of one of the pistons had damage from something..we suspect it was from the turbo )looks to be a new one on the engine). Pulled the Piston and the rings are fawked up looking..it is like they were chrome plated or something and flaking all along the edges. bearings $300, Rod $150 Piston $200 Plus gaskets $200? Whole engine rebuild kitw/ new sleeves and pistons, rings, bearings and gasket set $1600....so the whole thing is getting rebuilt...picked up a new oil pump (rebuilt) from mack $400..cha-ching! ouch! probably end up having $3k in it after this...sucks. We were trying to get out for $1200 w/ new bearings, and oil pump. Things just kept getting worse.

[Reckless]

3k for such an engine kit really aint bad. If ya have any questions, give me a call or pm. Ill be glad to help in anyway. That was one of mack's downfalls is the chrome plated rings. They saw it as a friction cutter but the coating wasnt good enough. Common problem,

[uglyota]

yeah close call huh? :flipoff2: