I'm not saying it's difficult to remove. I'm saying that I don't have the time to dick around in a ****ty area of Dallas searching for a part that is for a friend of a friend. Got any Internet or...
Type: Posts; User: 85cj7
I'm not saying it's difficult to remove. I'm saying that I don't have the time to dick around in a ****ty area of Dallas searching for a part that is for a friend of a friend. Got any Internet or...
I need an intake tube and air box (top and bottom) for a '96 f-250 7.3L
Any hints where I might find one? I really don't want to have to pull one myself. I also want stock, no cold...
Super easy to do. It look me about 30-min and all is right with the duramax again.
The o-rings for the fuel heater and the pressure valve were screwed. Mine was probably leaking from both.
Sprinkler system timers also come to mind.
I have the cognito upper arms and support kit. My truck is at 140K and I have changed the balljoints, tie rod ends and shocks out over the past few months. I still have a steering wheel wiggle and...
I watched this and ordered a $20 o-ring kit that will be here on Wed.
http://www.youtube.com/watch?v=9boIwwN-AHA
I will let you know how it goes.
It is leaking from the plug in sensor with the red wire. Seen here:
http://www.ebay.com/itm/2004-5-2013-LLY-LBZ-LMM-Duramax-Fuel-Filter-Assembly-W-Primer-Housing-12642623-/141030742673
2006 Chevy 6.6L Duramax
For the past week my truck has been hard to start when cold. It is fine when hot or and under all driving conditions. It is worse the longer it sits. Robbie heard what it...
Go to Rockauto and search for LUK Part# 07155. It is the complete kit with included one-piece flywheel. When checking out use 158540758994485 in the "How did you hear about use line" to save 5%....
I got it fixed today and even played around with the adjusting screws a bit and brought the front end of the truck down 3/4". I had to use a ball joint press on the driver side and a 7 ton 2-jaw...
How do I load it?
Basically just use the clamp to press the torsion bar off the crossmember?
SCARY STUFF.
I was turning into my neighborhood returning from work and heard a huge clunk and the driver front of the truck layed frame!
I limped it two blocks home, jacked it up and crawled...
Both the idler and pitman arms are fine. They are moog replacements and it has the Cognito supports as well (http://dmaxstore.com/index.php?main_page=product_info&cPath=23_67&products_id=107). It is...
I have that damn clunk in the steering column that I heard is super common on this era chevy. I also heard that there is a GM service package that comes with grease and plugs and you basically take...
OK!
I feel better!
Designed for either 2WD or 4WD models (commonized splined hub)
Genuine Timken is the original equipment manufacturer of this hub assembly for most 1999-2007 GMT800...
Yes it does fit. But I'm afraid to drive on it. Can anyone else look it up and see if they can find a different bearing for me. I keep finding that SP580310 is correct for my application.
I just found this:
New product info from TIMKEN please read:
Part Number:
SP580310
The subject part number is superseding the SP580304, SP580305, and the SP580306. This supersession is...
2006 Chevy 2500HD 2WD.
Trying to change the hub-bearings and I'm confused.
I have the new ones. Timken 580310. And I have the old ones off. They are obviously different. A little help please. The...
I ended up ordering through. . . http://www.fleetfilter.com/
It was 30% cheaper then running up to Napa, even with shipping, and their site says that they are 4 micron filters.
Napa has a "high efficiency'. Whatever the hell that means.
https://www.napaonline.com/Catalog/CatalogItemDetail.aspx?A=FIL3960XE_0259355444&An=599001+102006+50014+2014039
And their standard...
I need to change my fuel filter soon on my 06 duramax. What filters are good? Do I have to order something from Amsoil or a performance company or does Napa house brand suffice? Thanks.
Well then I guess I like them riced out. There are certainly some things added to this truck that I would not have paid for piecemeal but excluding the fuel filler and handles (which I have already...
I'm sorry my greatest single purchase I've ever made couldn't hold up to TAMOR web-wheeling standards. I'll enjoy driving it everyday, but keep hate'in.
*Ed, Thanks for your advice on the buy and...
2006 Silverado 2500hd CCSB, Exactly what I wanted
Duramax/Allison 6spd with 102K miles Didn't know much about them until researching and talking to Ed (Thanks!). Absolutely in love with this combo...
Just joined the diesel team!
http://i406.photobucket.com/albums/pp144/rkblankenship/DSC02905.jpg