Search:

Type: Posts; User: DRAGOONRANCH

Page 1 of 2 1 2

Search: Search took 0.15 seconds.

  1. Replies
    838
    Views
    375,853

    Hey Pete, meet RePete! :flipoff3:

    Hey Pete, meet RePete! :flipoff3:
  2. Replies
    838
    Views
    375,853

    I would unbolt the ram and see if it still does...

    I would unbolt the ram and see if it still does it. May be something internal that is binding.
  3. Replies
    838
    Views
    375,853

    The top set of numbers will be better for making...

    The top set of numbers will be better for making turns I believe.
  4. Replies
    838
    Views
    375,853

    tapered down towards the outside of the axle. ...

    tapered down towards the outside of the axle. The way you have it now though, if you ever decide to chop the ends off and turn it into a rear steer axle, that piece would be great to mount a ram on...
  5. Replies
    838
    Views
    375,853

    I went with the golf balls in mine. Let us know...

    I went with the golf balls in mine. Let us know how you like the ride.
  6. Replies
    838
    Views
    375,853

    Other than a pain in the ass when rotating tires,...

    Other than a pain in the ass when rotating tires, no. (and I really doubt you will be needing to do much rotating of your tires on this one. If you do like Scott, he just cuts one every trip so he...
  7. Replies
    838
    Views
    375,853

    Yep, the 2.75s would need to go in the back to...

    Yep, the 2.75s would need to go in the back to even them out. With your short wheel base I would think your turning radius would still be very acceptable. It's just a matter of looks. Does the...
  8. Replies
    838
    Views
    375,853

    Yes, shortened Chevy 44.

    Yes, shortened Chevy 44.
  9. Replies
    838
    Views
    375,853

    The flexalite controller had a temp probe like...

    The flexalite controller had a temp probe like that one where you put it in the fins of the radiator. I hope you can get it to work right for you, but my money is on 'not'. Make sure to put it as...
  10. Replies
    838
    Views
    375,853

    http://www.jegs.com/p/Be-Cool-Radiators/Be-Cool-Te...

    http://www.jegs.com/p/Be-Cool-Radiators/Be-Cool-Temperature-Sender/753117/10002/-1

    Use the 'hottest' two (195 and 210). If you run one continuously, the engine thermostat should keep the engine...
  11. Replies
    838
    Views
    375,853

    Looks good. :beer: A tree branh or one...

    Looks good. :beer:



    A tree branh or one really funky rock is the only way to get to that corner of the fender (kinda hard to tell from those pictures though). The tire should keep most...
  12. Replies
    838
    Views
    375,853

    Can it not be braced enough to keep it from...

    Can it not be braced enough to keep it from bending?
  13. Replies
    838
    Views
    375,853

    I bet they are tucked up a bit better than what...

    I bet they are tucked up a bit better than what the picture shows, and a cutoff wheel would get rid of anything that is really sticking down too far.
  14. Replies
    838
    Views
    375,853

    If you are going to run bushings at all three...

    If you are going to run bushings at all three points, then I would recommend the slip shaft like mine. When you go to flexing, it's going to put alot of strain on that single bushing especially if...
  15. Replies
    838
    Views
    375,853

    This I understand, just askin a question. ...

    This I understand, just askin a question. Sheesh. :rolleyes:


    :flipoff2: You know, I used to be a broke college student tryin to keep my pile of poo running also. Now I am just a broke...
  16. Replies
    838
    Views
    375,853

    Plenty of front driveshaft clearance? Mabey it...

    Plenty of front driveshaft clearance? Mabey it is just the pictures. Looks like a fairly clean job considering though. :gigem:
  17. Replies
    838
    Views
    375,853

    Just curious. How did you cut it, with the hot...

    Just curious. How did you cut it, with the hot wrench? If so, do you think that the heat will have affected the strength of it any?
  18. Replies
    838
    Views
    375,853

    Was that a piece of square tubing?

    Was that a piece of square tubing?
  19. Replies
    838
    Views
    375,853

    ya gonna have do do the spring plate also

    ya gonna have do do the spring plate also
  20. Replies
    838
    Views
    375,853

    speed hole 'em...

    speed hole 'em...
  21. Replies
    838
    Views
    375,853

    noice!!!

    noice!!!
  22. Replies
    838
    Views
    375,853

    Any plans on extra bracing?

    Any plans on extra bracing?
  23. Replies
    838
    Views
    375,853

    What motor and tranny do you have? Not that I...

    What motor and tranny do you have? Not that I will be able to help at all, but it might help others.
  24. Replies
    838
    Views
    375,853

    That's what is in the Cheby also. I really like...

    That's what is in the Cheby also. I really like it now that I got the problems w/ the hydro clutch system worked out. I 100% agree w/ Creighton on this one, don't go cheap unless you don't mind...
  25. Replies
    838
    Views
    375,853

    We did away with the mechanical on the treefitty...

    We did away with the mechanical on the treefitty and put an electric one in and never heard it, but I may have had the same issues as Jimmy too. ;)
Results 1 to 25 of 27
Page 1 of 2 1 2