i know brian broke several 1350 joints in the blazer. ive broke a **** ton of 1310 but then again those are 1310 and most came with the driveshafts i shortened and installed.....
i know brian broke several 1350 joints in the blazer. ive broke a **** ton of 1310 but then again those are 1310 and most came with the driveshafts i shortened and installed.....
Red 81 CJ5, 35's, 4.10 and detroit, 4 to 1 dana 300, tbi efi, flat belly, cage, chromos and auzzie in front... sometimes runs. body damage to come
Buy big driveshafts from a junkyard and retube them. Cut down on new driveshaft parts as much as you can.
'91 Bronco 351w, ZF5, D44 TTB, 9" rear swap with disk brakes, 37" toyos, method wheels, mastercraft seats, A/C and heat
The issue is with reverse shackles and my flex a "stock" driveshaft slip joint is too short. The longest available is used in Ford Pickups and offers 6" to 7"'s of slip, I need around 10" of slip. Additionally finding F250 cardon joints for front 4x4's is pretty hard.
-Karl
2006 Chevy K3500 4X4 - No J.B. Weld on it yet!
1982 thru 94 F-Series "The Klogger" AKA Transport on the road, on the trail, or on the trailer!
1965 Chevelle
1975 Corvette
the only reason that i would gernade 1350 daily on trips was because I was running them at extreme angles, judging by you above angle limits i would guess i was in the 15-20 degree range, that and lots of axle wrap. On the other hand I have broken a 1350 cv but that was because I was being stupid and full throttled a 3.5 - 4 foot ledge. All in all if I were to do it agian I would figure out how to run a 1410 at all ends and not cv's, which may be in my future
I run Woody's. they seem to have better track record and customer service for about the same $
Jonathan Tate
361.676.6466
2010 Dodge Ram 2500 4x4 6.7 MegaCab
2004 Jeep TJ
1992 Jeep YJ
2008 Jeep JKU
2013 Ford Explorer Sport (mama's go fast car)
I'm also running 1350 with minimal slip. My link setup doesn't move much.
Jonathan Tate
361.676.6466
2010 Dodge Ram 2500 4x4 6.7 MegaCab
2004 Jeep TJ
1992 Jeep YJ
2008 Jeep JKU
2013 Ford Explorer Sport (mama's go fast car)
It moved quite a bit at TCC last year
92 YJ
04 F-150 4x4
11 F-250 4x4
That would be a major advantage of link setups, you do not need much slip because the links themselves locate the axle.
-Karl
2006 Chevy K3500 4X4 - No J.B. Weld on it yet!
1982 thru 94 F-Series "The Klogger" AKA Transport on the road, on the trail, or on the trailer!
1965 Chevelle
1975 Corvette
I'd either do what Sparling said or just call Jesse and order what you need. I bought mine from Jesse and I've never touched my front one. Ever.
However, Scott identified my rear as matching a F250 front shaft, just shortened. I was blowing out the CVs (when I break a spring, the axle slides forward and jambs it up) and they were expensive. But now I'm able to fix them on the cheap. I picked up two for $175 from the junkyard and thanks to Doug I have a replacement and now have a spare.
The disco ball in my mouth, insinuates I'm ballin'
I've bought a couple 1350 flanges and 1410 yoke from Jesse, had great service and got the parts quick.
I had my driveshafts built by Houston Drivetrain Service (North side of 610 and Wayside). Both are double cardon, 1410's at the axles and 1350 flanges at the Stak. I took my front shaft back to them and had a long slip (like 16"s if I recall) added in. Works great now.
Who is Jesse?
-Karl
2006 Chevy K3500 4X4 - No J.B. Weld on it yet!
1982 thru 94 F-Series "The Klogger" AKA Transport on the road, on the trail, or on the trailer!
1965 Chevelle
1975 Corvette
Jesse is the owner of High Angle. His **** is pricey but his customer service is great and he's about the easiest way to just get it done.
On the 8th day god created the Super Swamper TSL and said "go forth and kick ass"