i got the jb conversions clocking kit in today it comes with new oil seal, shims, input shaft, bolts, studs, and clocking ring. Tomorrow i am going to modify the exhaust to clear the x-case, i'll show pics.
i got the jb conversions clocking kit in today it comes with new oil seal, shims, input shaft, bolts, studs, and clocking ring. Tomorrow i am going to modify the exhaust to clear the x-case, i'll show pics.
Last edited by 85cj7; 01-02-2009 at 12:31 AM.
i worked and finished the exhaust today. Its supposed to be temporary untill i can get to dallas and get it professionally redone. But i tried to make it as clean as possible because you never know how long its going to be untill this gets professionally done. Take a look at the pics and you will see why i couldn't clock the x-case untill the exhaust was worked on.
Last edited by 85cj7; 01-02-2009 at 12:32 AM.
heres pics of the modified exhaust. Again i don't think its to bad with what i had to work with.
why do you have to wait till you get it back to dallas to get the exhaust redone, there are shops here in town
i only trust one place when i comes to exhaust, there in wiley and the guy does exhaust work for collins bros, so he knows cjs and he can get everything as high as possible and do it right the first time.
Plenty of front driveshaft clearance? Mabey it is just the pictures. Looks like a fairly clean job considering though.
Originally Posted by Fredo
My bitch better have my money...
Through rain, sleet, or snow...
My whore better have my money...
Not half, not some, but all my cash...
'Cause if she don't,
I'm gonna put my foot in her ass.
There are no good exhaust shops in this area, just a lesser of evils
Ed, this is a multi step process in the world of daily driver
First is geting the dualish exhaust out of the way for the transfer case clocking
step 2 is getting exhaust redone
step 3 is measuring lowest thing hanging below the frame and building a skid plate around it
...
This I understand, just askin a question. Sheesh.
You know, I used to be a broke college student tryin to keep my pile of poo running also. Now I am just a broke working stiff w/ a bit more of disposable income tyrin to keep my pile of poo running.
My bitch better have my money...
Through rain, sleet, or snow...
My whore better have my money...
Not half, not some, but all my cash...
'Cause if she don't,
I'm gonna put my foot in her ass.
clocked the case
-everything went smoothly with the new clocking ring, input shaft, bearings, blah blah blah.
I had to wait untill today to wrestle the case in to its place because i needed someones help. Its clocked about 22.5 degrees according to my estimates.
It now sits at about 19" off the ground. I had to shorten the rear d-shaft about 1.5". and the shifter still needs to be figured out. If i can't get the single shifter to work than i'll just twin stick it.
Last edited by 85cj7; 01-02-2009 at 12:34 AM.
did you end up cutting a hole in the floor? if so lets see it
Red 81 CJ5, 35's, 4.10 and detroit, 4 to 1 dana 300, tbi efi, flat belly, cage, chromos and auzzie in front... sometimes runs. body damage to come
no i didn't have too, i did "clearance" it a little with a hammer, but after looking closer i really don't think that was even necessary.
heres the best before and after shot could manage.
your driveshaft looks likes its going to hit the crossmember
1976 F-100 Kustom Krawler
1976 F-150 Custom
1964 CJ5
I know a great exhaust guy in Wylie if you are looking for someone. His name is Rich, Rich's Performance Muffler (RPM)
http://www.richs-performance-mufflers.com/
Fred's Car
http://www.richs-performance-mufflers.com/92%20RS.jpg
St. John's old Impala
http://www.richs-performance-muffler...wer%20Tour.jpg
There used to be a pic of my scout on his site competing in the burnout contest, but no burnout pics anymore. Anyway, he does badass work and will run the exhaust however you want it.
Last edited by BMFScout; 04-07-2008 at 07:44 PM.
Boats and hoes
Stumble in to the liquor store
With a dollar-fifty for a bottle of wine,
I know just what I'm lookin for
Thunderbird will do just fine.
i think thsi is the same place flem was telling me to take it to. i was going to get the info from him later this week. thanks for the info.
Posting Permissions
Reply With Quote