Why don't you make something that looks like the spacer lifts for the newer strut trucks? Tubing and flat plate. Either that, or check and see if it's the same pattern and just buy them.
http://www.topguncustomz.com/Store/G...view=249061884
Why don't you make something that looks like the spacer lifts for the newer strut trucks? Tubing and flat plate. Either that, or check and see if it's the same pattern and just buy them.
http://www.topguncustomz.com/Store/G...view=249061884
"You know, this car is so fast, that giving Corvette owners this car, is kinda like giving an AK-47 to a pysch ward."
-Ron Fellows (Corvette C6R Team Driver)
metal depot or online metals, order four individual 6"x1" round bar 6061, put in drill press with hole saw.
...
Awesome, this is what I was looking forOriginally Posted by robertf03
Born to Kill
I just watched a spider dominate a fly on the wall outside, i thought would would travis do? and i did the opposite, spider lives!
For something that small you could use a piece of solid round stock and just drill the hole to the rightsize.
My bitch better have my money...
Through rain, sleet, or snow...
My whore better have my money...
Not half, not some, but all my cash...
'Cause if she don't,
I'm gonna put my foot in her ass.
Who or where could cut the roundstock 1" thick?
Born to Kill
I just watched a spider dominate a fly on the wall outside, i thought would would travis do? and i did the opposite, spider lives!
I'll pay for the metal if you cut it out with a jig saw with one blade.
'91 Bronco 351w, ZF5, D44 TTB, 9" rear swap with disk brakes, 37" toyos, method wheels, mastercraft seats, A/C and heat
If you go ed's route find someone with a bandsaw/chopsaw to cut it for you. If flems you might try a machine shop.
Or dont be puss and use a grinder with a cutoff wheel
He who dies with the most **** wins, after seeing your collection you are in the lead no doubt!
if you go my route they cut if for you, you are ordering a quantity of 2 @ whatever length you need. its all automated and goes right from the webserver to the bar feeder, they don't have someone add the cuts up and give you one piece.
Last edited by robertf03; 03-22-2011 at 12:08 AM.
...
I'm guessing aluminum would be ok for this type of spacer?
Born to Kill
I just watched a spider dominate a fly on the wall outside, i thought would would travis do? and i did the opposite, spider lives!
What is the shift pattern on a tera-low case? Standard case is 2h-4h-n-4l. I have shifted through this case over and over again and I get 4-4-n. That is with no 2 at all and possible 4h and 4l on the same side of n. What is wrong here.
Jonathan Tate
361.676.6466
2010 Dodge Ram 2500 4x4 6.7 MegaCab
2004 Jeep TJ
1992 Jeep YJ
2008 Jeep JKU
2013 Ford Explorer Sport (mama's go fast car)
Mine is same as stock 2 4h n 4l.
BDR
did you put the case together yourself? make sure the shift for is in properly.
Creighton, you have done stuff with that jeep that would make a goat go "holy ****!"
This is busa's case. Came out of his and bolted into mine. The only thing I installed in it was the speedo sensor. I don't see how that could cause any problems
Jonathan Tate
361.676.6466
2010 Dodge Ram 2500 4x4 6.7 MegaCab
2004 Jeep TJ
1992 Jeep YJ
2008 Jeep JKU
2013 Ford Explorer Sport (mama's go fast car)
how are you verifying the ranges?
Creighton, you have done stuff with that jeep that would make a goat go "holy ****!"
Don't know if they Are high or low but I can tell if both outputs are engaged or not. I will pull the speedo sensor and see if anything weird fell in there in transit and is acewing things up
Jonathan Tate
361.676.6466
2010 Dodge Ram 2500 4x4 6.7 MegaCab
2004 Jeep TJ
1992 Jeep YJ
2008 Jeep JKU
2013 Ford Explorer Sport (mama's go fast car)
Posting Permissions
Reply With Quote